Alpine DVA-9860 Bedienungshandbuch PDF herunterladen (Seite 36)

35-EN

Setting of Dolby Digital

Adjusting the speaker levels

The test tones help to make the volume adjustments of the different

speakers. When levels are equal, a strong sense of presence can be

heard from the different speakers at the listening position.

•Avoid stopping, pausing, switching the disc, cueing, fast-

forwarding or switching the audio channel of this unit while

making this adjustment. The setting is cancelled if the decode mode

is switched.

Check that Defeat mode is of f (page 19).

Press and hold CENTER f. for at least 2 seconds.

The audio processor control mode is activated.

Select the 5.1CH SETUP mode by pr essing

CENTER f. repeatedly .

Select OUTPUT LEVEL by pr essing g or f.

Press the Rotary encoder to select the speaker

to be adjusted.

The test tone is produced by the selected speaker.

Adjust the output level by tur ning and then

pressing the Rotary encoder.

Adjust each volume level for optimum balance by

repeating steps 5 and 6.

• The adjustment range for the different speakers is –10 dB - +10

dB.

• Adjust based on the front speakers.

When the setting is complete, pr ess and hold

CENTER f. for at least 2 seconds.

The unit returns to the normal mode.

Press CENTER f. to select another item to be set.

• If a speaker is set to off mode, that speaker’s level adjustment

cannot be made. Refer to “Speaker Setup” (page 34).

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 37.

Mixing bass sound to the rear channel

This function mixes the front channel audio signals to the audio

signals output from the rear speakers, improving the sound in the

vehicle’s rear seat.

•Avoid stopping, pausing, switching the disc, cueing, fast-

forwarding or switching the audio channel of this unit while

making this adjustment. The setting is cancelled if the Decode

mode is switched.

Check that Defeat mode is of f (page 19).

Press and hold CENTER f. for at least 2 seconds.

The audio processor control mode is activated.

Select the 5.1CH SETUP mode by pr essing

CENTER f. repeatedly .

Select REAR MIX by pr essing g or f.

Select REAR MIX ON/OFF by tur ning and then

pressing the Rotary encoder.

If ON is set, the audio signal which is output from the rear

speaker is mixed to the front audio signal.

Adjust the level (LEVEL) by tur ning and then

pressing the Rotary encoder.

The level can adjusted in five steps: –6, –3, 0, +3 and +6. The

higher the level, the more bass is output from the rear

speakers. (The effect differs according to the software (DVD,

etc.).)

When the setting is complete, pr ess and hold

CENTER f. for at least 2 seconds.

The unit returns to the normal mode.

Press CENTER f. to select another item to be set.

• This adjustment is ineffective when the rear speaker setup setting is

set to “OFF.”

•For linear PCM signals, the voice is output from the rear speaker

regardless of the REAR FILL and REAR MIX setting.

• When the setting is complete, it is recommended to store the setting

contents. For storing, refer to page 37.

Adjusting the acoustic image

In most installations, the centre speaker must be placed directly

between the front passenger and driver. Using this function, the centre

channel information is distributed to the left and right speakers. This

creates an acoustic image simulating a centre speaker directly in front

of each listener. Adjusting the centre width in PL II MUSIC (see

“Using the Pro Logic II Mode,” page 36), makes this function

ineffective.

•Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the Decode mode is switched.

Check that Defeat mode is of f (page 19).

Press and hold CENTER f. for at least 2 seconds.

The audio processor control mode is activated.

Select the 5.1CH SETUP mode by pr essing

CENTER f. repeatedly .

Select BI-PHANTOM by pr essing g or f.

Select BI-PHANTOM ON/OFF by tur ning and then

pressing the Rotary encoder.

If ON is set, the soundstage created is as if you are

positioned directly in front of the centre speaker by

distributing the centre speaker sound left and right.

Continued

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

Alpine DVA-9860 Bedienungshandbuch Seite 36

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Auto-Videosysteme Alpine DVA-9860